DisplayPort Fuser Guide
DisplayPort Fuser 指南
This guide explains how to set up a DisplayPort (DP) Fuser for use with a DMA card and how to fix the most common issues you may encounter during setup.
本指南说明如何设置 DisplayPort（DP）Fuser 以配合 DMA 卡使用，并说明如何修复设置过程中最常见的问题。
Guide for using a Fuser without a second monitor:
不使用第二显示器时使用 Fuser 的指南： https://vipercheats.com/fuser-without-second-monitor-guide
You can purchase our Fuser here:
你可以在这里购买我们的 Fuser： https://vipercheats.com/fuser
The HDMI Fuser setup guide can be found inside the DMA Cheats folder.
HDMI Fuser 设置指南可以在 DMA Cheats 文件夹中找到。
Recommended Hardware
推荐硬件
Recommended HDMI cable — HDMI 2.1
Recommended DisplayPort cable — DP 1.4
Your second PC or laptop must have at least one free HDMI port.
你的第二台电脑或笔记本必须至少有一个空闲 HDMI 端口。
If you don’t have a second PC, we recommend using a Mini PC.
Recommended operating system — Windows 10 or Windows 11
Connecting DisplayPort Fuser
连接 DisplayPort Fuser
1) On the second PC, open Display Settings.
在第二台电脑上打开 Display Settings。
2) Set the display scaling to 100%.
将显示缩放设置为 100%。
3) Choose the resolution you want to use.
选择你想使用的分辨率。
Important: The selected resolution and refresh rate must be supported by both monitors and the Fuser.
重要：所选分辨率和刷新率必须同时被两台显示器和 Fuser 支持。
If both of your monitors have the same specifications, set the resolution and refresh rate that the Fuser supports on both screens.
如果两台显示器规格相同，请在两块屏幕上设置 Fuser 支持的分辨率和刷新率。
Example from my setup: I use two 2K 165Hz monitors, but the Fuser supports up to 2K 144Hz.
以我的设置为例：我使用两台 2K 165Hz 显示器，但 Fuser 最高支持 2K 144Hz。
So I set both monitors to
所以我将两台显示器都设置为 2560×1440 at 144Hz.
If one monitor has a lower resolution or refresh rate, you must lower the settings on the other monitor to match it.
如果其中一台显示器的分辨率或刷新率较低，你必须降低另一台显示器的设置以匹配它。
Example: If your main monitor is 2K 165Hz and your second monitor is 1080p 60Hz, set both monitors to
例如：如果主显示器是 2K 165Hz，而第二显示器是 1080p 60Hz，请将两台显示器都设置为 1920×1080 at 60Hz.
Supported resolutions and refresh rates:
支持的分辨率和刷新率：
- 1920×1080 @ 60Hz
- 1920×1080 @ 144Hz
- 1920×1080 @ 165Hz
- 1920×1080 @ 240Hz
- 2560×1440 @ 144Hz
- 2560×1080 @ 165Hz
- 3440×1440 @ 60Hz
- 3440×1080 @ 100Hz
- 3840×2160 @ 60Hz
4) Select the refresh rate (it must be supported by both monitors and the Fuser).
选择刷新率（必须同时被两台显示器和 Fuser 支持）。
5) Apply the same settings on the main monitor:
在主显示器上应用相同设置：
- Scaling: 100%
缩放：100%。 - Resolution and refresh rate identical to the second monitor
分辨率和刷新率与第二显示器一致。
6) Connect the Fuser according to the picture below.
按下图所示连接 Fuser。
The main monitor must be connected to the Fuser using a DisplayPort cable.
主显示器必须使用 DisplayPort 线连接到 Fuser。
The second PC and the main PC’s GPU must be connected to the Fuser using HDMI cables.
7) Connect the Fuser to power and turn it on using the power button.
连接 Fuser 电源，并使用电源按钮打开它。
8) Using the remote control, select the resolution and refresh rate you configured earlier.
使用遥控器选择你之前配置的分辨率和刷新率。
Example: If you set 2560×1440 at 144Hz, press the 2K144 button on the remote.
9) On the second PC, open Display Settings again.
在第二台电脑上再次打开 Display Settings。
10) Under Multiple displays, select Duplicate these displays.
在 Multiple displays 下选择 Duplicate these displays。
It should turn out like this
结果应如下所示。
11) Press the Fusion button on the remote or directly on the Fuser.
按遥控器上的 Fusion 按钮，或直接按 Fuser 上的 Fusion 按钮。
This will broadcast the cheat from the second monitor to the main monitor.
这会把第二显示器上的辅助画面传输到主显示器。
If the cheat is not running, you will simply see a duplicated image.
如果辅助未运行，你只会看到复制的画面。
If the Fuser still does not work after completing all steps, watch the video manual and review the troubleshooting section below.
如果完成所有步骤后 Fuser 仍无法工作，请观看视频教程并查看下方故障排查。
Video Manual
视频教程
Main Monitor doesn’t work
主显示器无法工作
If the main monitor stays black, check the following:
如果主显示器一直黑屏，请检查以下内容：
- DisplayPort and HDMI cables are connected correctly
DisplayPort 和 HDMI 线已正确连接。 - No extra HDMI or DP cables are connected to the main monitor
主显示器没有连接额外的 HDMI 或 DP 线。 - The Fuser is powered on using the red power button
已使用红色电源按钮打开 Fuser。 - The selected resolution and refresh rate are supported and were chosen on the remote
所选分辨率和刷新率受支持，并已在遥控器上选择。
If none of this helps, disconnect all cables and repeat the setup from the beginning.
如果以上都无效，请断开所有线缆并从头重新设置。
Monitors aren’t working properly
显示器无法正常工作
If the image appears stretched, cropped, or unstable, make sure:
如果画面被拉伸、裁切或不稳定，请确认：
- The same resolution and refresh rate are set on both monitors
两台显示器设置了相同的分辨率和刷新率。 - The selected values are supported by the Fuser
所选参数被 Fuser 支持。 - “Duplicate these displays” is enabled on the second PC
No Supported resolution
没有支持的分辨率
If your monitor settings are not supported, lower the resolution or refresh rate to the closest supported option.
如果显示器设置不受支持，请将分辨率或刷新率降低到最接近的受支持选项。
Example: If your monitor is 4K 120Hz, switch to 4K 60Hz or 2K 120Hz.
例如：如果显示器是 4K 120Hz，请切换到 4K 60Hz 或 2K 120Hz。
Both monitors must support the chosen resolution and refresh rate.
两台显示器都必须支持所选分辨率和刷新率。
Remote control doesn’t work
遥控器无法工作
Make sure a CR2025 battery is installed correctly in the remote control.
确认遥控器中已正确安装 CR2025 电池。
Where to download?
在哪里下载？
You can download DMA Cheats folder here
你可以在这里下载 DMA Cheats 文件夹 — https://vipercheats.com/download
